E-PROJECTTOPICS

Chemical Engineering

Discover and download richly documented academic research across all disciplines – all at your fingertips.

REFURBISHMENT OF FLUID FLOW DEMONSTRATION UNIT

ABSTRACTThe refurbishment of the fluid flow demonstration unit was carried out in the Chemical Engineering pilot plant laboratory of the Institute of Management and Technology Enugu.The refurbishment process was carried out to ensure adequate functioning of the unit, to allow the continuous use o...

Chemical Engineering Type: PROJECT

📄 53 pages | 🧠 7551 words | 📚 5 chapters

353 views

View Full Project

SHORT-TERM LIME PRETREATMENT AND ENZYMATIC CONVERSION OF SAWDUST INTO ETHANOL

ABSTRACT The utilization of lignocellulosic biomass as feedstock for the production of fuel ethanol has attracted considerable interests in the last few decades. The emergence of new technologies has provided hope for fuel ethanol potential uses. Lignocellulose is a valuable alternative energy so...

Chemical Engineering Type: PROJECT

📄 232 pages | 🧠 43963 words | 📚 5 chapters

404 views

View Full Project

Investigating Bio-Diesel Production using Potash from Agricultural Wastes

ABSTRACT The application of potassium hydroxide (KOH) extracts from four different biomass materials: Water hyacinth, Coconut husk, ripe plantain peels and palm frond  in the trans-esterification of two vegetable oils;  refined rapeseed and crude jatropha oils has been carried out. Pota...

Chemical Engineering Type: PROJECT

📄 246 pages | 🧠 39668 words | 📚 5 chapters

441 views

View Full Project

CONSTRUCTOIN OF AN OPEN STEAM DISTILLATOIN COLUMN

ABSTRACT    We constructed an open steam distillation column with the following specifications:-FOR THE COLUMNHeight of column     =    500mmLength of pot        =    50mmDiameter of pot    &n...

Chemical Engineering Type: PROJECT

📄 38 pages | 🧠 4046 words | 📚 6 chapters

426 views

View Full Project

CONSTRUCTION OF PROPELLER AGITATOR

ABSTRACT    Propeller agitator is a specialized of various types of substances.  It consists of three basic components which are the shaft, blade and the vessel.    In the construction, mild steel was chosen due to it's inherent properties.  After the procu...

Chemical Engineering Type: PROJECT

📄 48 pages | 🧠 6005 words | 📚 6 chapters

411 views

View Full Project

UTILIZATION STUDIES OF ENUGU COAL

ABSTRACT    This study has its theme as a utilization studies of Enugu coals with the view of studying its properties, classification, preparation storage etc comparing coals obtained from different locations.    The Enugu coal is a sub-bitummous and non coking coal....

Chemical Engineering Type: PROJECT

📄 61 pages | 🧠 8324 words | 📚 6 chapters

476 views

View Full Project

DESIGN AND CONSTRUCTION OF A REFRIGERATING UNIT

ABSTRACT    The design and construction of s refrigerating unit is handled from the knowledge of the working principles of laws of thermodynamics.    The size of the containing vessel i.e the case as established to be of 45cm by 32 cm in dimension. The Angle iron mil...

Chemical Engineering Type: PROJECT

📄 28 pages | 🧠 2849 words | 📚 4 chapters

330 views

View Full Project

THE FABRICATION OF STRONG AND MEDIUM SIZED WHEELBARROW

ABSTRACTThe fabrication of a standard wheel barrow is a very cheap and easy to construct it the right materials are selected and also if the right sequence of fabrication is observed. However, in the construction of a standard wheel barrow, the amount of load the materials can withstand when cons...

Chemical Engineering Type: PROJECT

📄 27 pages | 🧠 3960 words | 📚 4 chapters

410 views

View Full Project

THE FABRICATION FOR A SET OF SIEVES AND SAKER

ABSTRACT    The fabrication of a set of sieves and shaker was carried out in paliton workshop, Enugu. After a thorough analysis on the suitable materials to be used in fabrication, galvanized steel was chosen due to its advantages over materials of fabrication. The fabrication was ...

Chemical Engineering Type: PROJECT

📄 56 pages | 🧠 6649 words | 📚 6 chapters

475 views

View Full Project

THE CONSTRUCTION OF SIEVE EQUIPMENT

ABSTRACT    The sets of seizes with shocker which was fabricated and assembled in the chemical engineering pilot plant was aimed at providing the students with a machine that will aid them in practical involving the separation of solid particles. Besides this, it was also fabricate...

Chemical Engineering Type: PROJECT

📄 47 pages | 🧠 6851 words | 📚 5 chapters

372 views

View Full Project

REPAIR OF STOP CLOCKS

ABSTRACT    Stop clocks are devices for indicating time duration for the occurrence of two events after a passage of time. They are usually powered by batteries and they measure time in unit of seconds. Most clocks stop working as a result of the inability of the main spring to mak...

Chemical Engineering Type: PROJECT

📄 33 pages | 🧠 3774 words | 📚 5 chapters

340 views

View Full Project

CONSTRUCTION OF TURBINE MIXER

ABSTRACTThe Turbine Mixer was Fabricated at the Mechanical Engineering Workshop of Institute of Management and Technology, EnuguThe method of the fabrication of the Turbine Mixer involves a preliminary computation of the dimensions of the standard Turbine in relation to the dimension  of the...

Chemical Engineering Type: PROJECT

📄 44 pages | 🧠 5427 words | 📚 5 chapters

381 views

View Full Project

CONSTRUCTION OF STEEL CUPBOARD - Version 2

ABSTRACT    A workshop cupboard is a facility designed from mild steel for the storage of various materials, like book material and non-book materials e.g. workshop tools, labouratory wares and reagents, etc; after operations in a chemical labouratory, mechanical workshop, or else ...

Chemical Engineering Type: PROJECT

📄 73 pages | 🧠 9796 words | 📚 7 chapters

355 views

View Full Project

CONSTRUCTION OF STEEL CUPBOARD

ABSTRACT    The project work "Construction of standard steel cupboard" was constructed at the mechanical workshop. During the construction, various hand and machinery tools (equipment) such as electric welding machine, hammers, guillote, folding machine, spraying machine, milling m...

Chemical Engineering Type: PROJECT

📄 39 pages | 🧠 5068 words | 📚 7 chapters

429 views

View Full Project

CONSTRUCTION OF SHEEL AND TUBE HEAT EXCHANGER

ABSTRACT    The aim of this project was to construct shell and tube heat exchanger with fixed boundless. A heat exchanger that would cool 5 x 5 x 10 - 3 kg/s of steam at a calculated heat load of 152 - 395/S was fabricated. The steam is to reach the heat exchanger from a distillati...

Chemical Engineering Type: PROJECT

📄 47 pages | 🧠 5463 words | 📚 7 chapters

364 views

View Full Project

« 1 2 3 4 »